|
PureBytes Links
Trading Reference Links
|
Thanks, it's up and running. I had placed the device=%systemroot.... in the
config.nt.txt file, SB config.nt
Chas
----- Original Message -----
From: "Bob Fulks" <bfulks@xxxxxxxxxxxx>
To: "ChasWaring" <cwwaring@xxxxxxxxxxxxxx>
Cc: <omega-list@xxxxxxxxxx>
Sent: Sunday, May 21, 2000 2:50 PM
Subject: Re: TS4/Win2000 secutiry block missing
> I just went through this today and got it working.
>
> I installed TS 4.0 build 21 from the CD once. I got "SSIACT.386 not found"
error.
>
> Then I went to the "SYSTEM.INI" file, found the [386Enh] section. Make
sure the
> line "DEVICE=SSIACT.386" is there.
>
> I reinstalled again from the CD ROM. Then downloaded the build 27 patch
from the Omega web site and installed it. This got me to the "Security block
not found" message.
>
> I then found the FAQ on the Support web page under Running TS4.0 on
Windows 2000 and did everything specified there and it worked!
>
> I tried several things and do not exactly recall everything in order but
this is close.
>
> Bob Fulks
>
> >I have made all these changes reccommended by Omega's FAQ
> >and no success.
> >
> >Any help would be appreciated.
> >
> >Charlie
> >
> >
> >>>>>>>>>>>>>>
> >The only issue encountered to date between the products has been related
to
> >the Security Block drivers. In order for the block to be recognized, the
> >steps outlined in the Ntreadme.wri file located in the
Omega\Prog\Drivers\NT
> >directory must be completed. The text of this file is included below. In
> >addition, the following lines must be added to the system.ini file as the
> >first two lines under the [386Enh] Section as follows:
> >
> >[386Enh]
> >device=ssiact.386
> >SSI_LPT=1
> >
> >1 is used for LPT1, 2 for LPT2, etc. if the block is attached to a port
> >other than LPT1.
> >
> >Text of Ntreadme.wri file:
> >
> >NOTE: Using Windows 2000, the System32 directory is located in the
Windows
> >directory, not WINNT as outlined below. Please use the Windows\SYSTEM32
or
> >Windows\SYSTEM32\DRIVERS\ directory where applicable.
> >
> >Manual Installation of the Security Block under Windows NT
> >
> >The following is a list of instruction on how to manually install the
> >drivers for the Security Block under the Windows NT operating system:
> >
> >Step 1
> >
> >Copy the following files located in your OMEGA\PROG\DRIVERS\NT directory
to
> >the WINNT\SYSTEM32\DRIVERS\ directory:
> >
> >SSIDDDP.SYS
> >
> >SSIPDDP.SYS
> >
> >Step 2
> >
> >Copy the following file located in your OMEGA\PROG\DRIVERS\NT directory
to
> >the WINNT\SYSTEM32\ directory:
> >
> >SSIVDDP.DLL
> >
> >Step 3
> >
> >Add the following line to the CONFIG.NT file in Windows NT WINNT\SYSTEM32
> >directory.
> >
> >DEVICE=%SystemRoot%\system32\drivers\SSIDDDP.SYS
> >
> >Step 4
> >
> >Locate your MS-DOS prompt. At the prompt type the letter of the drive in
> >which your Omega directory resides followed by the colon and the pressing
> >Enter or Return key.
> >
> >Then Type in the following line followed by pressing the Enter or Return
> >key.
> >
> >CD\OMEGA\PROG\DRIVERS\NT\SSIREGI install
> >
> >If you are installing your Security Block on LPT1, STOP HERE and restart
> >your computer. You have completed the installation of the Security Block.
If
> >you are installing the Security Block on another LPT port continue with
the
> >remaining steps.
>
|