PureBytes Links
Trading Reference Links
|
Thanks for explaining, but i meant that the signal was correct but i
do not want it to be effective when G1 has been going down for
example 5 days. I added your advice
NumDownBarsG1 = BarsSince( G1 >= Ref(G1,-1));
Buy = Cross(G0,G1)AND Cross(G0,G2) OR Cross(G0,G1) AND BarsSince(Cross
(G0,G2)) <= 10 OR Cross(G0,G1); // OR Cross(G0,G2) AND NumDownBarsG1
< 5);
only i get failure messages at the last part: AND NumDownBarsG1 < 5);
--- In amibroker@xxxxxxxxxxxxxxx, "gp_sydney" <gp.investment@xxx>
wrote:
>
> One comment about your conditions:
>
> >> Buy = Cross(G0,G1)AND Cross(G0,G2) OR Cross(G0,G1)
> >> AND BarsSince(Cross (G0,G2)) <= 10 OR Cross(G0,G1);
>
> When mixing multiple AND and OR conditions in the same expression,
you
> should use brackets to indicate operator precedence. For example:
>
> (X AND Y) OR Z
>
> is not the same thing as:
>
> X AND (Y OR Z)
>
> While there is a predefined order of precedence when no brackets are
> used, I doubt most people would be sure of what it is, whereas
> brackets make it obvious.
>
> Regards,
> GP
>
>
> --- In amibroker@xxxxxxxxxxxxxxx, "rijnaars" <rijnaa@> wrote:
> >
> > Thanks Ed
> > I will show you the rules i use know.
> >
> > Buy = Cross(G0,G1)AND Cross(G0,G2) OR Cross(G0,G1) AND BarsSince
(Cross
> > (G0,G2)) <= 10 OR Cross(G0,G1);
> >
> > Only sometimes Buy = Cross(G0,G1) gives a wrong signal
> >
> > i do not wnat it to act if G1 has been going down for instance
for
> > last 7 days how do i implement this condition.
> >
> > (--- In amibroker@xxxxxxxxxxxxxxx, "Edward Pottasch"
<empottasch@>
> > wrote:
> > >
> > > hi,
> > >
> > > not sure exactly what you mean but maybe you could use OR
instead
> > of AND, so Buy = Cross(A1,A3) OR BarsSince(Cross(A1,A2)) <= 2;
> > >
> > > but on an array level you can construct more detailed
constraints
> > using:
> > >
> > > Buy = IIF(Cross(A1,A3) AND BarsSince(Cross(A1,A2)) <= 2,1, etc
> > >
> > > or just using OR in your contraint rule Buy = (constraint
rule1) OR
> > (constraint rule 2) OR (constraint rule 3) etc; like:
> > >
> > > Buy = (Cross(A1,A3) AND BarsSince(Cross(A1,A2)) <= 2) OR (Cross
> > (A1,A3)) OR () etc;
> > >
> > > if you explain in detail how your constraint should work I can
> > write it for you.
> > >
> > > regards, Ed
> > >
> > >
> > >
> > >
> > >
> > > ----- Original Message -----
> > > From: rijnaars
> > > To: amibroker@xxxxxxxxxxxxxxx
> > > Sent: Monday, October 06, 2008 9:48 AM
> > > Subject: [amibroker] Re: Help on conditional Buy signals
> > >
> > >
> > > Thank you very much Ed this is what i needed
> > > maybe you can help me on another aspect as well.
> > >
> > > if i do not want the cross signal to react if A1 crosses A3
where
> > A3
> > > has been going down for the last 4 days forinstance.
> > > What condition should i then implement?
> > > thanks in advance
> > >
> > > --- In amibroker@xxxxxxxxxxxxxxx, "gp_sydney"
<gp.investment@>
> > > wrote:
> > > >
> > > > Ed,
> > > >
> > > > That's saying the A1/A3 cross must be before the A1/A2
cross,
> > not
> > > > after. It should be the other way around:
> > > >
> > > > Buy = Cross(A1,A3) AND BarsSince(Cross(A1,A2)) <= 2;
> > > >
> > > > Regards,
> > > > GP
> > > >
> > > >
> > > > --- In amibroker@xxxxxxxxxxxxxxx, "Edward Pottasch"
> > <empottasch@>
> > > > wrote:
> > > > >
> > > > > this can be done like:
> > > > >
> > > > > buy = Cross(A1,A2) AND barssince(Cross(A1,A3)) <= 2;
> > > > >
> > > > > rgds,Ed
> > > > >
> > > > >
> > > > >
> > > > > ----- Original Message -----
> > > > > From: rijnaars
> > > > > To: amibroker@xxxxxxxxxxxxxxx
> > > > > Sent: Monday, October 06, 2008 8:08 AM
> > > > > Subject: [amibroker] Help on conditional Buy signals
> > > > >
> > > > >
> > > > > I want to use some conditions in a buy cross signal but i
do
> > > not know
> > > > > how to add it.
> > > > >
> > > > > For instance :
> > > > >
> > > > > i have a buy signal buy = Cross(A1,A2)AND Cross(A1,A3)
> > > > >
> > > > > so in this case A1 crosses both A2 and A3
> > > > > now i like to have a signal as well when the second cross
is
> > > made
> > > > > within 2 days after the first cross how do i make this
> > > condition?
> > > > >
> > > >
> > >
> >
>
------------------------------------
**** IMPORTANT ****
This group is for the discussion between users only.
This is *NOT* technical support channel.
*********************
TO GET TECHNICAL SUPPORT from AmiBroker please send an e-mail directly to
SUPPORT {at} amibroker.com
*********************
For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
http://www.amibroker.com/devlog/
For other support material please check also:
http://www.amibroker.com/support.html
*********************************
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/amibroker/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/amibroker/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:amibroker-digest@xxxxxxxxxxxxxxx
mailto:amibroker-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
amibroker-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|