|
PureBytes Links
Trading Reference Links
|
TS2000i needs some parenthesis in the denomenator otherwise a straight line
is the result. They are in the book but were left out in the omega posts.
MD = MD[ 1 ] + ( c - MD[ 1 ] ) / (K * period * power( ( c / MD[ 1 ] )),
----- Original Message -----
From: "Benjamin Blanco" <ezlang@xxxxxxxxxxxxxxxxxx>
To: "!omega-list" <omega-list@xxxxxxxxxx>
Sent: Friday, December 06, 2002 1:39 PM
Subject: Re: McGinley Dynamics
> Usually, a technique that references a previous value of itself will
specify
> the starting value of MD on the first bar. For example:
>
> inputs: k( .6 ), period( 9 ) ;
> vars: MD( 0 ) ;
>
> if CurrentBar = 1 then
> MD = Close { close in this illustration could be replaced with any
> appropriate value }
> else begin
> if K <> 0 and MD[ 1 ] <> 0 then
> MD = MD[ 1 ] + ( c - MD[ 1 ] ) / K * period * power( ( c / MD[ 1 ] ),
> 4 ) ;
> end ;
>
> plot1( MD, "MD" ) ;
>
>
> Best regards,
>
> Benjamin Blanco,
> EasyLanguage Specialist
> ( former TradeStation Technologies, Inc. employee of six years )
> http://www.benjaminblanco.com/
>
> EasyLanguage is a registered trademarks of TradeStation Technologies, Inc.
>
> ----- Original Message -----
> From: "Clyde Lee" <clydelee@xxxxxxxxxx>
> To: "Benjamin Blanco" <ezlang@xxxxxxxxxxxxxxxxxx>; "!omega-list"
> <omega-list@xxxxxxxxxx>
> Sent: Friday, December 06, 2002 9:44 AM
> Subject: Re: McGinley Dynamics
>
>
>
>
> How will MD[1] ever get to be anything but Zero.
>
>
> - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> Clyde Lee Chairman/CEO (Home of SwingMachine)
> SYTECH Corporation email: clydelee@xxxxxxxxxxxx
> 7910 Westglen, Suite 105 Office: (713) 783-9540
> Houston, TX 77063 Fax: (713) 783-1092
> Details at: www.theswingmachine.com
> - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
> ----- Original Message -----
> From: "Benjamin Blanco" <ezlang@xxxxxxxxxxxxxxxxxx>
> To: "!omega-list" <omega-list@xxxxxxxxxx>
> Sent: Thursday, December 05, 2002 11:07 PM
> Subject: Re: McGinley Dynamics
>
>
> > Here is a sample of the EasyLanguage you could use to check for division
> by
> > zero.
> >
> > inputs: k( .6 ), period( 9 ) ;
> > vars: MD( 0 ) ;
> >
> > if K <> 0 and MD[ 1 ] <> 0 then
> > MD = MD[ 1 ] + ( c - MD[ 1 ] ) / K * period * power( ( c / MD[ 1 ] ),
> 4 )
> > ;
> >
> > plot1( MD, "MD" ) ;
> >
> >
> > Best regards,
> >
> > Benjamin Blanco,
> > EasyLanguage Specialist
> > ( former TradeStation Technologies, Inc. employee of six years )
> > http://www.benjaminblanco.com/
> >
> > EasyLanguage is a registered trademarks of TradeStation Technologies,
Inc.
> >
> > ----- Original Message -----
> > From: "Trey Johnson" <dickjohnson3@xxxxxxxxxxxxxx>
> > To: <omega-list@xxxxxxxxxx>
> > Sent: Thursday, December 05, 2002 11:04 AM
> > Subject: McGinley Dynamics
> >
> >
> > The code for this indicator in Kaufman's book, "Trading Systems and
> > Methods," is the following:
> >
> > inputs: k(.6),period(9);
> > vars:MD(0);
> >
> > MD=MD[1]+(c-MD[1])/K*period*power((c/MD[1]),4);
> >
> > plot1(MD,"MD");
> >
> > However, it doesn't work. I keep getting the error message: "attempt to
> > divide by zero." I tried a couple of different things and still can't
get
> it
> > to work. Any suggestions?
> > Thanks in advance,
> > Trey Johnson
> >
>
>
>
>
>
|