PureBytes Links
Trading Reference Links
|
Lionel,
Having lived in Brussels years ago and being raised in Detroit and having
made too many beer runs into Windsor, I would have to agree with your
recommendations. You know you better be careful with these recommendations
as our list mother may start flaming you about your motives in pushing these
brews.
As a teenager, my favorite was Cinci Cream (the Canadian brewed version).
Guy
" When I die, I want to go peacefully like my grandfather did, in his sleep.
Not yelling and screaming like the passengers in his car."
-----Original Message-----
From: owner-metastock@xxxxxxxxxxxxx [mailto:owner-metastock@xxxxxxxxxxxxx]On
Behalf Of Lionel Issen
Sent: Sunday, August 27, 2000 7:34 AM
To: metastock@xxxxxxxxxxxxx
Subject: Beer
Guy:
If you are a beer connoisseur try Belgium and Canadian beers. The alcohol
content of Belgian beers runs from about 7% to 9% depending on the brew.
Some Canadian beers run as high as 6% alcohol. Both countries' beers are
tasty too.
Disclaimer: I have no financial interest in any brewery or distillery. These
comments are provided for information only. Use at your own risk (big grin).
Lionel Issen
lissen@xxxxxxxxx
----- Original Message -----
From: Guy Tann <grt@xxxxxxxxxxxx>
To: <metastock@xxxxxxxxxxxxx>
Sent: Sunday, August 27, 2000 2:20 AM
Subject: RE: Precision and MS calculations
> Steve,
>
> Lost that darn beer again. Probably skunky by now.
>
> I'll be in "D" next Thursday for 4 days visiting my folks. I'll toss down
a
> couple of coney islands down for you as well. :)
>
>
>
> Guy
>
> Never be afraid to try something new. Remember, amateurs built the ark,
> professionals built the Titanic.
>
> -----Original Message-----
> From: owner-metastock@xxxxxxxxxxxxx
[mailto:owner-metastock@xxxxxxxxxxxxx]On
> Behalf Of Steve Karnish
> Sent: Friday, August 25, 2000 6:04 AM
> To: metastock@xxxxxxxxxxxxx
> Subject: Re: Precision and MS calculations
>
> Guy,
>
> Too much Stroth's beer at an early age.
>
> Steve Karnish
> Cedar Creek Trading
> http://www.cedarcreektrading.com
> ----- Original Message -----
> From: Guy Tann <grt@xxxxxxxxxxxx>
> To: Metastock User Group <metastock-list@xxxxxxxxxxxxx>
> Sent: Thursday, August 24, 2000 9:11 PM
> Subject: Precision and MS calculations
>
>
> > List,
> >
> > Well I gave up and went back to square one. I couldn't figure out how a
> > variable could calculate correctly from 12/11/99 to 8/9/00 and then fail
> the
> > next day and then work correctly again. First I wrote 7 Clipper
programs
> > which I used to print out each variable. I checked my MS calculations
for
> > each variable against these printouts. The first 8 variables calculated
> > correctly.
> >
> > The ninth variable didn't! What was weird was that every day calculated
> > correctly until the 2nd day from the end. I double-checked the inputs
and
> > they were in complete agreement (I exported my MS data into Clipper to
> > insure both systems that were using the same data). I then went back
and
> > double-checked each value that was part of this calculation. One of my
> > variables was off slightly for one of these days. I went back and
recoded
> > my MS code and broke the calculation into 6 steps to equal the code in
the
> > Clipper program. So now I have identical code in both modules and you
> would
> > think that the results would be identical. Wrong, buckwheat!
> >
> > For the life of me, I'm at a loss. It's probably something to do with
MS
> > and precision, but in this case, following rounding, I use Int() to
> capture
> > only the whole number and drop any fractions. If anyone has a
suggestion,
> > I'm open to it. Our numbers are too sensitive to not be able to trust
the
> > results of a simple calculation. If this was a complex calculation, I
> might
> > possibly understand a variance. In this case the correct answer is -3
> (and
> > yes, I did calculate it manually to make sure) while MS came up with -2.
> > I think I'm going to take a day off and clear my head. This is why I
get
> so
> > frustrated trying to use MS. How could a program calculate correctly
for
> > 99.994% of the time and then blow it on that one day?
> > Tomorrow, I'm planning on printing out the intermediate results from
both
> > Clipper and MS to see if I can see where this thing is going wrong. I'm
> too
> > tired tonight.
> >
> > I need a break. Where did I put that beer?
> >
> > Guy
> >
> > Never be afraid to try something new. Remember, amateurs built the ark,
> > professionals built the Titanic.
> >
>
>
|