|
PureBytes Links
Trading Reference Links
|
Hi Howard and all,
yes SPSO is the inbuild particle optimizer.... When I optimize for Ulcer Index I do not take everytime the best choice, as I do not do it when I optimize for %Net Perf or CAR/MDD. Eaxmple: If I have let's say 3 parameters 100x100x100 I would get 1mn options. If I optimize for %Net Perf with SPSO the list would be about 5000-7000 results. But as I do not want to choose the best %Net Perf but the highest %Net Perf with a high UPI, a high CAR/MDD, high RRR, low StDev I would decide to use the parameters for maybe the 2nd or 3rd etc. rated result. But this is not possible if I directly use the inbuild WalkForward Test of Amibroker, as the system uses always the first choice and not the best choice.
If I would optimize directly for RRR, I got sometimes as first choice just 1-2 trades as the StDev was the lowest there, but I would never use this parameters. That is why I was searching for an alternative.
Many thanks and kind regards,
dubi
--- In amibroker@xxxxxxxxxxxxxxx, Howard B <howardbandy@xxx> wrote:
>
> Hi Bisto --
>
> Thanks. From the original posting, I was thinking that SPSO was a metric.
>
> Dubi --
>
> The choice of optimization method (exhaustive, cmae, ...) and metric (Ulcer
> Index, CAR/MDD, k-ratio, ...) are independent. The optimization portion of
> the walk forward will be carried out using the optimization method you
> request in you afl code with the OptimizerSetEngine statement. The
> selection of which of the alternatives tested to use for the out-of-sample
> run will be determined by the metric you set in the Optimization Target box
> on the Walk Forward tab of the AA Settings.
>
> Or did I misinterpret your question?
>
> Thanks,
> Howard
>
>
> On Fri, Nov 13, 2009 at 3:39 AM, Bisto <bistoman73@xxx> wrote:
>
> >
> >
> > I suppose: Standard Particle Swarm Optimization
> >
> > Bisto
> >
> >
> > --- In amibroker@xxxxxxxxxxxxxxx <amibroker%40yahoogroups.com>, Howard B
> > <howardbandy@> wrote:
> > >
> > > Hi Dubi --
> > >
> > > What is SPSO?
> > >
> > > Thanks,
> > > Howard
> > >
> > > On Wed, Nov 11, 2009 at 9:07 AM, dubi1974 <gonzales74@> wrote:
> > >
> > > >
> > > >
> > > > Hi!
> > > >
> > > > Is it possible to optimize a system (for e.g. best net performance %)
> > with
> > > > SPSO but then use the highest Ulcer Performance Index or CAR/MDD and
> > use
> > > > then this parameters for the out of sample test for the next period in
> > the
> > > > Walk Forward Test of Amibroker? I know I could do this in separate
> > steps,
> > > > but I would like to automize that. Or does someone know an other
> > solution
> > > > for this?
> > > >
> > > > Many thanks and kind regards,
> > > >
> > > > dubi
> > > >
> > > >
> > > >
> > >
> >
> >
> >
>
------------------------------------
**** IMPORTANT PLEASE READ ****
This group is for the discussion between users only.
This is *NOT* technical support channel.
TO GET TECHNICAL SUPPORT send an e-mail directly to
SUPPORT {at} amibroker.com
TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at
http://www.amibroker.com/feedback/
(submissions sent via other channels won't be considered)
For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
http://www.amibroker.com/devlog/
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/amibroker/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/amibroker/join
(Yahoo! ID required)
<*> To change settings via email:
amibroker-digest@xxxxxxxxxxxxxxx
amibroker-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
amibroker-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|