PureBytes Links
Trading Reference Links
|
TA -
I have to go out, so let me see if I can explain quickly.
1. The AFL will add all symbols from group 253 that satisfy the condition. You only need to use the current symbol because the symbol loop is built into the AFL. If you want to run it again group 253, you would set the Apply To to Use Filter and the group to 253. If you did that, AA is looping through the symbols for you and you would only need -
if ( StrLeft( Name( ), 1 ) == "~" AND
StrLeft( Name( ), 3 ) != "~~~" )
{
CategoryAddSymbol( Name( ), catgorywatchlist, 61 );
}
2. See above for how to code what you expressed -
"I had the following two conditions is that all my composite tickers have one "~" as the first character in their symbol. I also want to exclude all equity tickers that have "~~~" as the first three characters in their symbols."
Note - this will process anything that begins with "~" including for example, "~ABC". This may or may not be what you want.
-- BruceR
--- In amibroker@xxxxxxxxxxxxxxx, "ta" <tagroups@xxx> wrote:
>
> Thanks Bruce. If I scan only on the current symbol, It would only add that
> on symbol (although the trace statement shows all symbols were added). The
> reason I had the following two conditions is that all my composite tickers
> have one "~" as the first character in their symbol. I also want to exclude
> all equity tickers that have "~~~" as the first three characters in their
> symbols. TIA
>
>
>
> if ((StrLeft(Name(),1)=="~") AND (StrLeft(Name(),2)!="~~"))
>
>
>
> From: amibroker@xxxxxxxxxxxxxxx [mailto:amibroker@xxxxxxxxxxxxxxx] On Behalf
> Of Bruce
> Sent: Wednesday, September 30, 2009 10:34 AM
> To: amibroker@xxxxxxxxxxxxxxx
> Subject: [amibroker] Re: Add addtocompiste generated ticker to a watchlist
>
>
>
>
>
> Close. See changes and run the following as a SCAN on the CURRENT SYMBOL
> only -
>
> TickerList = CategoryGetSymbols( categoryGroup, 253);
> for( i=0; (Ticker=StrExtract( TickerList, i)) != ""; i++)
> {
> if (StrLeft(ticker, 2)=="~~")
> {
> CategoryAddSymbol(ticker, categoryWatchlist, 61);
> _TRACE( "Added - " + ticker );
> }
> }
> Buy=0;
>
> -- BruceR
>
> --- In amibroker@xxxxxxxxxxxxxxx <mailto:amibroker%40yahoogroups.com> , "ta"
> <tagroups@> wrote:
> >
> > Since, I did not hear from anybody I assume that there is not a way. As a
> > result I wrote the following code to read the addtocomposite created
> tickers
> > from group 253 and add them to watchlist 61. However, it takes about 19
> > minutes to do this. Does anybody see a way to improve the speed of my
> code?
> > Perhaps Tomasz can comment on why this process is so slow? TIA
> >
> >
> >
> > TickerList = CategoryGetSymbols( categoryGroup, 253);
> > for( i=0; (Ticker=StrExtract( TickerList, i)) != ""; i++)
> > {
> > if ((StrLeft(Name(),1)=="~") AND (StrLeft(Name(),2)!="~~"))
> > CategoryAddSymbol("", categoryWatchlist, 61);
> > }
> >
> > Buy=0;
> >
> >
> >
> > From: amibroker@xxxxxxxxxxxxxxx <mailto:amibroker%40yahoogroups.com>
> [mailto:amibroker@xxxxxxxxxxxxxxx <mailto:amibroker%40yahoogroups.com> ] On
> Behalf
> > Of ta
> > Sent: Tuesday, September 29, 2009 9:56 PM
> > To: amibroker@xxxxxxxxxxxxxxx <mailto:amibroker%40yahoogroups.com>
> > Subject: [amibroker] Add addtocompiste generated ticker to a watchlist
> >
> >
> >
> >
> >
> > I did not see a flag that would add a ticker created by addtocomposite
> > function to a watchlist. Is there a way of doing this as the new tickers
> are
> > created? TA
> >
>
------------------------------------
**** IMPORTANT PLEASE READ ****
This group is for the discussion between users only.
This is *NOT* technical support channel.
TO GET TECHNICAL SUPPORT send an e-mail directly to
SUPPORT {at} amibroker.com
TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at
http://www.amibroker.com/feedback/
(submissions sent via other channels won't be considered)
For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
http://www.amibroker.com/devlog/
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/amibroker/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/amibroker/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:amibroker-digest@xxxxxxxxxxxxxxx
mailto:amibroker-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
amibroker-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|