|
PureBytes Links
Trading Reference Links
|
maybe....
IF ( MACDline == Signalline) // histogram value equals zero
X = lastvalue(MACDline);
Plot (X,"", colorblack);
--- In amibroker@xxxxxxxxxxxxxxx, Dennis Brown <see3d@xxx> wrote:
>
> Yes, I have it set to 100%. The absolute values of the indicator will
> vary wildly, depending on the price and volatility of the stock. I
> plot ES, so the values are quite large at times.
>
> BR,
> Dennis
>
> On Jun 26, 2009, at 5:58 PM, monitorit wrote:
>
> > If that's all you needed, the color change would be best. But, I
> > think the solution I suggested would work... you would still plot/
> > see value very high or low just within a section defined by pane*1/
> > minvalue [at least it has for me]. BTW, presently what is the upper
> > and lower bounds of the MACD in relationship to the height of the
> > pane? Is it 100% of the pane height?
> > Dan
> >
> > --- In amibroker@xxxxxxxxxxxxxxx, Dennis Brown <see3d@> wrote:
> >>
> >> Dan,
> >>
> >> This is what I usually do for indicators when I know the range of
> >> values. However, MACD is an unbounded indicator, so I don't know how
> >> large the values are. It is only the zero crossings and relative
> >> peaks that are useful info here.
> >>
> >> I just thought there would be some simple shortcut to actually
> >> scanning the visible bars for the min/max values to use in the plot
> >> statements. I think I will just switch colors of the MACD from red
> >> to
> >> green if it is above or below zero instead of resorting to yet
> >> another
> >> loop.
> >>
> >> Thanks,
> >> Dennis
> >>
> >>
> >> On Jun 26, 2009, at 4:40 PM, monitorit wrote:
> >>
> >>> Dennis,
> >>> Hi. You might try this- Place a value in minvalue section but none
> >>> in maxvalue section [I think maybe a value like 2 equates to 1/2
> >>> pane height] of your MACD and zero plot statements.
> >>> Also,styleNoRescale in the zero plot statement. This worked for me
> >>> when I wanted to plot a histogram and a dot on the top of the
> >>> histogram. Not sure if it works with a line. If it doesn't, you
> >>> could try plotohlc with H=max(0,my#) and L=min(0,my#).
> >>>
> >>> Dan
> >>>
> >>> --- In amibroker@xxxxxxxxxxxxxxx, Dennis Brown <see3d@> wrote:
> >>>>
> >>>> Hello,
> >>>>
> >>>> This must be simple, but my AFL brain is fried today. I have an
> >>>> MACD
> >>>> plot on top of my main price chart, and I want to plot a zero line
> >>>> over it. It is plotted as StyleOwnScale of course. I can't use
> >>>> StyleLeftAxis because I am using it for something else. I guess I
> >>>> could do something to figure out where the visible high and low
> >>>> values
> >>>> of the MACD are, but it seems like it should be easier than that.
> >>>>
> >>>> TIA,
> >>>> Dennis
> >>>>
> >>>
> >>>
> >>>
> >>>
> >>> ------------------------------------
> >>>
> >>> **** IMPORTANT PLEASE READ ****
> >>> This group is for the discussion between users only.
> >>> This is *NOT* technical support channel.
> >>>
> >>> TO GET TECHNICAL SUPPORT send an e-mail directly to
> >>> SUPPORT {at} amibroker.com
> >>>
> >>> TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at
> >>> http://www.amibroker.com/feedback/
> >>> (submissions sent via other channels won't be considered)
> >>>
> >>> For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
> >>> http://www.amibroker.com/devlog/
> >>>
> >>> Yahoo! Groups Links
> >>>
> >>>
> >>>
> >>
> >
> >
> >
> >
> > ------------------------------------
> >
> > **** IMPORTANT PLEASE READ ****
> > This group is for the discussion between users only.
> > This is *NOT* technical support channel.
> >
> > TO GET TECHNICAL SUPPORT send an e-mail directly to
> > SUPPORT {at} amibroker.com
> >
> > TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at
> > http://www.amibroker.com/feedback/
> > (submissions sent via other channels won't be considered)
> >
> > For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
> > http://www.amibroker.com/devlog/
> >
> > Yahoo! Groups Links
> >
> >
> >
>
------------------------------------
**** IMPORTANT PLEASE READ ****
This group is for the discussion between users only.
This is *NOT* technical support channel.
TO GET TECHNICAL SUPPORT send an e-mail directly to
SUPPORT {at} amibroker.com
TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at
http://www.amibroker.com/feedback/
(submissions sent via other channels won't be considered)
For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
http://www.amibroker.com/devlog/
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/amibroker/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/amibroker/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:amibroker-digest@xxxxxxxxxxxxxxx
mailto:amibroker-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
amibroker-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|