|
PureBytes Links
Trading Reference Links
|
Hi Mike,
I try the code you provide here, But I'm not able to add it as part of my other code.
Can u help please.
Thanks an advince
--- In amibroker@xxxxxxxxxxxxxxx, "Mohammed" <softnews2003@xxx> wrote:
>
> Hi Mike,
>
> I appreciated your reply. I will try that.
>
>
> Thanks again.
> Regards
>
>
> --- In amibroker@xxxxxxxxxxxxxxx, "Mike" <sfclimbers@> wrote:
> >
> > Try something like the following (untested)
> >
> > if (LastValue(BarsSinceCrossedGreen) < LastValue(BarsSinceCrossedRed)) {
> > // Last cross ever was up
> > } else {
> > // Last cross ever was down
> > }
> >
> > Or possibly
> >
> > if (SelectedValue(BarsSinceCrossedGreen) < SelectedValue(BarsSinceCrossedRed)) {
> > // Last cross up to selection was up
> > } else {
> > // Last cross up to selection was down
> > }
> >
> > Mike
> >
> > --- In amibroker@xxxxxxxxxxxxxxx, "Mohammed" <softnews2003@> wrote:
> > >
> > >
> > > Hi all,
> > >
> > > For the following code I'm using two values to show the number of bars
> > > since MACD cross. One value for up and one for down. These values
> > > showing both in the chart page, I would like to show only the last
> > > values depending to cross if the cross up I need to show the values for
> > > up and if it for down cross I need to show the value for down only.
> > > Instead of showing both values.
> > >
> > > One_Houre_Green_Cross = Cross(MACD(), Signal());
> > > One_Houre_Red_Cross = Cross(Signal(), MACD());
> > > BarSinceCrossgreen = BarsSince( One_Houre_Green_Cross);
> > > BarSinceCrossred = BarsSince( One_Houre_Red_Cross);
> > > BarSinceCrossUp = StrFormat(" %g ", BarSinceCrossgreen, SelectedValue(
> > > ROC( C, 1 ) ) );
> > > BarSinceCrossDown = StrFormat(" %g ", BarSinceCrossred, SelectedValue(
> > > ROC( C, 1 ) ) );
> > >
> > > GfxSelectFont( "Arial", 12, 700 );
> > > GfxSetBkMode( 1 );
> > > GfxSetTextColor( colorGreen);
> > > pxHeight = Status( "pxchartheight" );
> > > t = pxHeight;
> > > x5 = 101;
> > >
> > > GfxTextOut( BarSinceCrossUp, x5, t -50);
> > > GfxSetTextColor( colorRed);
> > > GfxTextOut( BarSinceCrossDown, x5, t -25);
> > > GfxSelectFont( "Arial", 9, 700 );
> > > GfxSetTextColor( colorBlack);
> > >
> > > Bar = "Bar";
> > > x4 = 78;
> > >
> > > GfxTextOut( Bar, x4, t -50) ;
> > > GfxTextOut( Bar, x4, t -25) ;
> > >
> > > Any one can help please.
> > > Regards
> > >
> >
>
------------------------------------
**** IMPORTANT PLEASE READ ****
This group is for the discussion between users only.
This is *NOT* technical support channel.
TO GET TECHNICAL SUPPORT send an e-mail directly to
SUPPORT {at} amibroker.com
TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at
http://www.amibroker.com/feedback/
(submissions sent via other channels won't be considered)
For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
http://www.amibroker.com/devlog/
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/amibroker/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/amibroker/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:amibroker-digest@xxxxxxxxxxxxxxx
mailto:amibroker-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
amibroker-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|