Keith
Concerning Yahoo, many times my mails appeared 4 days later. Once, 6
days later.
This sluggishness happens every time I post throught Thunderbird.
Via Web, it seems OK.
Best regards
--- In amibroker@xxxxxxxxxps.com,
Keith McCombs <kmccombs@xx.> wrote:
>
> Ozzy --
> Yes, at this point it seems to be easier to live with all the
extra
> columns than to learn how OLE works.
>
> I believe, long ago, before the suggestion page was implemented on
AB
> site, that I suggested to TJ that no columns be displayed by
default,
> and that the all columns and their widths be specified
programmatically
> and/or in a settings page. Obviously the suggestion was not
> implemented. IMHO, it would be a significant improvement over the
> present system.
>
> I did get your previous response. But I understand your concern. I
had
> to post my request three times before it finally went through. My
two
> others were on 1/14, 1:04am and 1/16, 1:39am. Just recently these
were
> finally delivered. Yahoogroups can be unbelievably slow at times.
> -- Keith
>
> ozzyapeman wrote:
> >
> > Seems my response did not go thru. Reposting:
> >
> > Keith - did not get around to implementing any OLE. Living
with the
> > extra columns for now. But if I do write any code for it,
will post it
> > here in the future.
> >
> > --- In amibroker@xxxxxxxxxps.com
<mailto:amibroker%40yahoogroups.com>,
> > Keith McCombs <kmccombs@> wrote:
> > >
> > > Ozzy --
> > > Any chance you have already gone through the pain of
implementing the
> > > appropriate OLE code. If so, would it be possible to
share it
and some
> > > brief instructions on how to use it? That would be
greatly
appreciated.
> > >
> > > Thank you.
> > > -- Keith
> > >
> > > ozzyapeman wrote:
> > > >
> > > > I asked this Q on the board a few weeks ago, and
the consensus was
> > "no".
> > > >
> > > > But you can export the report using OLE and run an
exploration
showing
> > > > only the columns you want:
> > > >
> > > > http://finance.groups.yahoo.com/group/amibroker/message/132540
> > <http://finance.groups.yahoo.com/group/amibroker/message/132540>
> > > > <http://finance.groups.yahoo.com/group/amibroker/message/132540
> > <http://finance.groups.yahoo.com/group/amibroker/message/132540>>
> > > >
> > > > --- In amibroker@xxxxxxxxxps.com
<mailto:amibroker%40yahoogroups.com>
> > <mailto:amibroker%40yahoogroups.com>,
> > > > "huanyanlu" <huanyan2000@> wrote:
> > > > >
> > > > > Hi,
> > > > >
> > > > > I just learned to add some custom metrics into
backtester. But
> > then I
> > > > > find that some of the built-in metrics in the
backtester are not
> > > > > important in my way of analysis. So is there a
way to show only
> > some of
> > > > > the built-in metrics , together with my added
custom metrics ?
> > > > >
> > > > > According to the help file, it seems that the
backtester
object can
> > > > > allow you either show all the built-in
metrics, or not show
any of
> > > > > them .
> > > > >
> > > > > Thanks for any help
> > > > >
> > > > > Huanyan
> > > > >
> > > >
> > > >
> > >
> >
> >
>