[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[amibroker] Re: Identify bar for actual Buy



PureBytes Links

Trading Reference Links

Thanks for everyones help and advise - back to reading the docs.

Just never expected the transition to AB to be so difficult - 
probably easier if I could wipe prior knowledge.

Thamks

Graham
>
> Hello,
> 
> By default you are operating on ARRAYS not on single values.
> 
> A must-read for everyone starting out:
> http://www.amibroker.com/guide/h_understandafl.html
> 
> In short: RECURSIVE calculations need a FOR loop and [] operator
> http://www.amibroker.com/guide/keyword/for.html
> 
> "For" loop and array subscript operator [] gives you acces
> to INDIVIDUAL values.
> 
> Best regards,
> Tomasz Janeczko
> amibroker.com
> ----- Original Message ----- 
> From: "Graham Johnson" <grahamj@xxx>
> To: <amibroker@xxxxxxxxxxxxxxx>
> Sent: Sunday, January 27, 2008 8:00 AM
> Subject: [amibroker] Re: Identify bar for actual Buy
> 
> 
> > Hi
> > 
> > The bottom line with this is that I want to be able to set a stop 
and 
> > have control over it.
> > 
> > After thinking it through, I decided that the first step was to 
set 
> > the stop for the first Buy signal and keep it at the same value 
until 
> > a Sell signal and then set it to 0 again.
> > 
> > Seemed like a great theory but the stop value is reset at each 
bar 
> > and therefore does not maintain a constant value.  Maybe it is a 
> > mindset thing - my professional experience was with procedural 
> > languages and AFL taxes my thinking processes sometimes - maybe 
> > something about teaching an old dog new tricks...
> > 
> > Anyway, the snippet of code for setting the stop is as follows
> > 
> > Buy = Ref(vaValidEntry,-1) AND Low <= Ref(vaLimitEntry, -1);
> > BuyPrice = Min(Open, Ref(vaLimitEntry, -1));
> > vaIStopVal = ATR(vISATRPer) * vISMult;
> > vaInitStop = 0;
> > vaInitStop = IIf(((Buy == 1) AND (Ref(vaInitStop, -1) == 0)) , 
> > BuyPrice - (Ref(vaIStopVal, -1)), Ref(vaInitStop, -1));
> > _TRACE(" | buy: " + Buy + " | stop: " + vaInitStop + " | 
PrevStop: " 
> > + Ref(vaInitStop, -1));
> > 
> > Any ideas as to where I've gone wrong and why it is resetting the 
> > value each bar, please.
> > 
> > Graham
> > 
> >> I'm sure that a solution for this has been on the forum, but - 
> > after 
> >> much searching......
> >> 
> >> Code is for a Long system that does not pyramid.
> >> 
> >> I am looking to manually code the disaster stop, so need to be 
able 
> > to 
> >> set the stop on the day that the trade is actually entered, and 
not 
> >> have the water muddied by subsequent signals that are not taken 
> > because 
> >> the system does not pyramid.
> >> 
> >> I know that the ApplyStop function is available, but I need to 
> > acquire 
> >> the technique for controlling stops programatically.
> >> 
> >> Hopefully, this is clear.
> >> 
> >> Graham
> >>
> > 
> > 
> > 
> > 
> > Please note that this group is for discussion between users only.
> > 
> > To get support from AmiBroker please send an e-mail directly to 
> > SUPPORT {at} amibroker.com
> > 
> > For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
> > http://www.amibroker.com/devlog/
> > 
> > For other support material please check also:
> > http://www.amibroker.com/support.html
> > 
> > Yahoo! Groups Links
> > 
> > 
> >
>




Please note that this group is for discussion between users only.

To get support from AmiBroker please send an e-mail directly to 
SUPPORT {at} amibroker.com

For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG:
http://www.amibroker.com/devlog/

For other support material please check also:
http://www.amibroker.com/support.html
 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/amibroker/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/amibroker/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:amibroker-digest@xxxxxxxxxxxxxxx 
    mailto:amibroker-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    amibroker-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/