Very kind of you to say so.
I was speaking directly to Tomasz, so using the imperial we in not
appropriate in this case.
And since you are extra sharp today, have you followed the Abbot and
Costello routine with regard to my other question.
Getting a straight answer here is about as easy as getting AFL to
work correctly on the first pass.
I am asking if you can plot on the chart from within the code running
an exploration/backtest, without pasting code into the chart itself.
I know all about the trade arrows, thats not the question.
--- In amibroker@xxxxxxxxxps.com,
"Fred" <ftonetti@xx.> wrote:
>
> We saw it ... and yes ... you are "blessed" ...
>
> --- In amibroker@xxxxxxxxxps.com,
"Homar Simpson" <x77777x@> wrote:
> >
> > Guess you didn't see my previous post, I concluded that some code
> > that was buried within a chart was causing a conflict. A clean chart
> > works fine. I could not determine the exact code that is
> problematic.
> >
> > I know folks are often pointed toward memory or hardware, but I
> > suspect that is actually the problem , oh, maybe 1 out of 100 times,
> > especially if NO OTHER APPS but the affected one are displaying
> issues.
> >
> > I would hesitate to blame memory until many other avenues were
> > explored. In my 25 plus years I think hardware was the issue twice
> > out of 1000 problems.
> >
> >
> > --- In amibroker@xxxxxxxxxps.com,
"Tomasz Janeczko \(groups\)"
> > <groups@> wrote:
> > >
> > > Most probably you have hardware problem (memory timing problems
or
> > underpowered power supply)
> > > which results in instability.
> > >
> > > Use "torture test" in Prime95 program to check your
hardware for
> > stability.
> > >
> > > Best regards,
> > > Tomasz Janeczko
> > > amibroker.com
> > > ----- Original Message -----
> > > From: "Homar Simpson" <x77777x@>
> > > To: <amibroker@xxxxxxxxxps.com>
> > > Sent: Friday, June 29, 2007 1:50 AM
> > > Subject: [amibroker] Re: Buggy install or what?
> > >
> > >
> > > > Am I the only one blessed with this erratic problem. Fails,
then
> > > > works a few hours later with same code, Next day fails
again.
> with bad
> > > > multiple bogus arrows and access violations
> > > >
> > > > ver 4.90
> > > >
> > > >
> > > > --- In amibroker@xxxxxxxxxps.com,
"Homar Simpson" <x77777x@>
> wrote:
> > > > >
> > > > > Having a bad time with very erratic behavior with the
> backtester,
> > > > > and show trade arrows. Sometimes it works, but mostly
Im
> getting
> > > > > bogus displays of arrows on every bar, even when show
trade
> arrows
> > > > > only is selected.
> > > > >
> > > > > Seeing some access violations as well.
> > > > >
> > > > > Haven't rebooted to test, but could the access
violations
> cause
> > > > > instability even when AB is closed and restarted? I
didn't
> > think so,
> > > > > but anything is possible.
> > > > >
> > > >
> > > >
> > > >
> > > >
> > > > Please note that this group is for discussion between users
> only.
> > > >
> > > > To get support from AmiBroker please send an e-mail
directly to
> > > > SUPPORT {at} amibroker.com
> > > >
> > > > For NEW RELEASE ANNOUNCEMENTS and other news always check
> DEVLOG:
> > > > http://www.amibroker.com/devlog/
> > > >
> > > > For other support material please check also:
> > > > http://www.amibroker.com/support.html
> > > >
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> >
>